Trình duyệt của bạn đã tắt chức năng hỗ trợ JavaScript.
Website chỉ làm việc khi bạn bật nó trở lại.
Để tham khảo cách bật JavaScript, hãy click chuột vào đây!

How to Paint Cornhole Boards

Thứ sáu - 26/04/2024 23:11

Table of contents

If you love playing cornhole but don't want to buy an expensive pair of boards, make and paint your own. Once you've assembled the basic wooden boards, prepare the wood by filling, sanding, and priming them. Determine how glossy you want the boards to be and then use a brush or roller to apply the paint. Always let the boards dry completely before adding coats of paint. Embellish your cornhole boards with designs, decals, or stickers.

Method 1

Method 1 of 3:

Sanding and Priming the Boards

1
Set up your work area. Choose a well-ventilated space to paint the cornhole boards to prevent the buildup of paint fumes. Paint the boards outside or use an indoor room that has windows or doors you can open. Lay down drop cloths on a flat work surface to prevent the paint from making a mess.
- For example, if you work in your garage, keep the garage door open and lay drop cloths directly on the garage floor or a work bench.

License: Creative Commons<\/a>
\n<\/p>

\n<\/p><\/div>"}

Fill any holes with wood filler. Check your cornhole boards for small holes or knots in the wood. Dip a putty knife into a container of wood filler so you have just a little bit on the end. Push the putty knife against the holes to fill them with the wood filler. Run the putty knife over the wood to smooth out the filler. Let the wood filler dry according to the manufacturer's instructions.^{[1] X Research source}
Most manufacturers recommend letting the filler dry for about 8 hours.

Advertisement

License: Creative Commons<\/a>
\n<\/p>

\n<\/p><\/div>"}

Smooth the boards using sandpaper. Sanding wood before painting is a must. Choose a medium grit piece of sandpaper or sanding block with a range of 60 to 100. Rub it over the plain boards to smooth over any bumps or dried wood filler. It will improve the surface of the boards so the primer and paint go on easier.^{[2] X Research source}
If you prefer, you can use an electric sander to smooth the boards down.

License: Creative Commons<\/a>
\n<\/p>

\n<\/p><\/div>"}

Run a clean cloth or rag under clean water and wring it out. Rub the damp cloth over the boards to remove any dust from sanding the boards. Let the boards dry completely before you prime them.

License: Creative Commons<\/a>
\n<\/p>

\n<\/p><\/div>"}

Choose a white oil-based primer to use on the cornhole boards. Open the primer and use a paint stirrer to briefly mix the primer. Dip your brush into the primer or pour some into a paint tray so you can use a roller. Use the brush or roller to apply a thin layer of primer over both cornhole boards. Let the primer dry for at least 1 hour or according to the manufacturer's instructions.^{[3] X Research source}

Oil-based primer works best with wood because it will penetrate deep into the wood and dry harder than water-based primers.

Primer is designed to bond the paint to the surface. Any bare surface that has never been painted needs to be primed.

Method 2

Method 2 of 3:

Painting Base Layers

License: Creative Commons<\/a>
\n<\/p>

\n<\/p><\/div>"}

If you're creating a detailed pattern or design, take a pencil and draw the design directly on the primed boards. This will give you an outline for painting the boards.
If you're making geometric designs (such as angles that point toward the hole) use a ruler or yardstick to draw straight lines.

Step 2 Choose a paint for the cornhole boards.

Decide how glossy you want the painted boards to be. For a slight shine, choose a semigloss paint. For very shiny boards, pick a high gloss paint. Determine if you want to paint the boards a single color or if you want to paint each of them different colors.

For example, you might paint 1 of the boards red and the other board blue. For detailed boards, use different colors or hues on each board.

Step 3 Use a brush or roller to apply a layer of paint to the boards.

Open the paint and use a paint stirrer to combine the pigment and binders in the paint. Either dip a paintbrush into the paint can and wipe the excess on the rim of the can or pour the paint into a paint tray. Dip a roller into the tray and roll it back a few times to load the roller with paint. Brush or roll a thin layer of paint evenly over the board.

If you dislike painting or want to quickly get an even layer of paint on the boards, buy spray paint. Wear a face mask when using the spray paint so you don't breathe in the fumes. Spray the paint slowly and evenly so it doesn't pool on the boards.^{[4] X Research source}

To ensure that overspray from the spray paint won't get on any surrounding items, move things away from your work space and lay a drop cloth over the entire area.